Forum Navigation
Post History: GeoAstra Official
Check and Update Firmware
Before configuring the X8-M1 as an RTK base, ensure the firmware vers …In: How to Configure the GeoAstra X8-M1 in RTK Base Mode?
3 days ago
Starting from firmware version V1.2.16, the GeoAstra X8-M1 supports the RTK Base feature. To check w …In: How to Update the Firmware of GeoAstra X8-M1 to Version V1.2.16?
3 days ago
The distance from the bottom of the antenna to its phase center is 99mm.In: Which part of the X8-M1 does the positioning reading refer to?
3 months ago
Yes, we can customize the RTU609BT with an RS-232 interface instead of a USB interface. However, ple …In: Can you customize an RS-232 version of the RTU609BT?
3 months ago
When you connect a Bluetooth GNSS receiver (e.g., TOP608BT or RTU609BT) to Windows, you’ll notice tw …In: Why do two “Serial over Bluetooth” COM ports appear when pairing the Bluetooth GNSS receiver to Windows?
3 months ago
https://video.bynav.com/sv/48baf48d-1949ceeb243/48baf48d-1949ceeb243.mp4
In: Video Demo: GeoAstra X8-M1 Pole Stick & Stand (optional accessories)
3 months ago
For details, please refer to this article:
ByNav X8-M1 Data Logging Demo
Note: The ByNav X8-M1 is …In: Demo: Data Logging with RTKPlot App & GeoAstra X8-M1 GNSS Receiver
3 months ago
As shown in the screenshot below, the “RTCM Source” has four options. I will explain their meanings …In: Explanation of "RTCM Source" Options in the ByCenter App
5 months ago
The X8-M1 uses a standard 1/4”-20 UNC thread, which is the most common mount thread size for consume …In: What type of mount thread does the X8-M1 use?
5 months ago
(GBoxTools was renamed to ByCenter in December 2024. This instruction was created when the ByCenter …In: How to Install the ByCenter Android App?
5 months ago
The X8-M1 uses a spiral antenna, with positioning readings referenced from the center of the antenna …In: Which part of the X8-M1 does the positioning reading refer to?
5 months ago
To activate the slave antenna, please use the following 2 commands:rangeha 1
gphdt com1 1You can in …In: How to turn on the slave antenna of RTU608BT?
8 months ago
GeoAstra RTB609BT can function as a standalone Bluetooth GPS receiver; however, it does not have a b …In: Is it possible to connect to the GeoAstra RTB609BT GNSS receiver via Bluetooth without using the USB cable?
9 months ago
GeoAstra RTB609BT is using Prolific PL2303GL usb chip. It is a newer version of the USB-to-serial ch …In: Where to Download the Windows 10/11 Driver for GeoAstra RTB609BT GNSS Receivers?
9 months ago
GeoAstra RTU609BT can function as a standalone Bluetooth GPS receiver; however, it does not have a b …In: Is it possible to connect to the GeoAstra RTU609BT GNSS receiver via Bluetooth without using the USB cable?
9 months ago
GeoAstra RTU609BT is using Prolific PL2303GC usb chip. It is a newer version of the USB-to-serial ch …In: Where to Download the Windows 10/11 Driver for GeoAstra RTU609BT GNSS Receivers?
9 months ago
GeoAstra NTRIP Caster itself offers global coverage, allowing your RTK Bases and Rovers access from …In: Do you have any coverage map?
10 months ago
In most scenarios, it is acceptable to use an L1 and L2 antenna with an L1, L2, and L5 GNSS receiver …In: Can I use a L1 and L2 Antenna with an L1, L2, and L5 RTK GNSS Receiver?
10 months ago
Appearance and Structure
Nylon Braided Cables: These cables have a protective layer of nylon …In: Main Differences Between GeoAstra RTU608BT Nylon Braided usb Cable vs TOP608BT Regular usb Cable
10 months ago
When the mount point is created, the default value for the Authentication field is set to “B”. Howev …In: Extra field in NTRIP source table
10 months ago
Thank you for reporting the issue (the duplicated “carrier” field in the source table)! The issue ha …In: Extra field in NTRIP source table
10 months ago